Top 9 Tips To DIY Your Sprinkler System

If you are like me, you want to DIY certain things around your home so you don’t have to pay someone else to do it.

So before you start installing the sprinkler system, be sure to follow these instructions.

To begin, draw out a plan for your sprinkler system, call a professional to mark any power or piping lines, check your water pressure, contact your city for permits, plan how you’re going to dig the trenches, decide where the water source will be, count the number of valves, calculate the amount of piping needed, and decide what kind of sprinklers you want.

Make a plan for where you want the sprinklers to go.
To begin, you’ll need to draw out a plan for your sprinkler system if you want to do it yourself.

Sprinkler systems are never put up in the same way again.

This is because no two yards are the same.

In our community, everyone has different acreage, so it would be impossible for one individual to go off of another person’s design.

Plus, this would enable you to set up the sprinkler system precisely the way you would like it to go. To begin, you’ll need to get a sense of the lay of the land.

If you don’t know the property boundaries, you may have to get a surveyor to come out and mark it for you (particularly do this to make sure neighbors are satisfied) (especially do this to make sure your neighbors are happy).

It’s good to find out how much a surveyor will charge you before hiring them to come out and mark your property borders.

If there is fencing already up, then you probably won’t have to worry about a surveyor; simply keep inside your side of the fence.

Once you know the property boundaries, you should be able to walk off your yard, so you have an exact measurement.

Grab someone from your residence and ask them to assist you. Then acquire the longest measuring tape you have.

After that, stand in a corner and have the other person stretch out the measuring tape until it has gone as far as possible.

If the measuring tape doesn’t run out before they reach the end of the yard, that’s great; record the measurement and go on to the next end of the yard.

If you still have some distance to go, ask your buddy to stand at the end of the measuring tape, and then you stretch the measuring tape out from where they are, continuing along the same end of the yard.

Continue this till you arrive at the finish. Once reaching the end of the yard, walk down the next line of the yard. Do this until you’ve acquired all 4 lines of the yard.

Then you have all the dimensions you need to build your yard. You may use the dimensions to create a yard plan on paper. Next, you may perform one of two things:

  • Send a sprinkler manufacturer a drawing of your yard.


Some sprinkler manufacturers will design a sprinkler system for you, including a plan and a shopping list of all the parts you’ll need.

That way, you’ll end up buying their stuff and your own. However, I cannot ensure that the manufacturer will return your plans even if you choose this option, which is the most straightforward.

However, if they are willing to do it for free, it is worth a shot.

  • Write out the plans by yourself.


Writing it yourself may not be the greatest solution if you don’t know what you are doing.

However, with a few Google searches, you should be able to figure out the ideal approach to map out your garden.

You’ll also need to know a little bit about how pipes function. It should be a breeze if you can get over it. Either way, you’ll be prepared to go.

Make a note of any electricity or pipelines that need to be marked.

Depending on where you reside, various lines are buried at varying depths. Digging for sprinklers doesn’t need to be too deep, but you should still have someone come out to draw the lines.

Even if you are just falling down a few inches, you should still call. Who comes out to draw the lines depends on where you dwell.

One person may be sent to mark the electricity and water lines in certain locations. But some places will require you to write a request to the corporation that controls the lines.

In this situation, the local water company would be responsible for marking the water lines, while your electric utility would be responsible for marking the power lines.

As a result, you’ll need to identify the appropriate party. Once again, the easiest approach to learn about the criteria is to do a Google search.

A second alternative is to phone your local municipal administration and ask who should be contacted. There is a strong chance they know anything or maybe have the phone numbers you need.

And their marking of the lines is probably going to be free. As a result, they’re providing this service free of charge to ensure that you don’t accidentally damage any underground pipes.

When the lines are marked, make sure you don’t dig within two feet of the markings to be on the safe side.

Check your water pressure.


Sprinklers need a certain amount of water pressure, so be sure you have it. So making sure you have the optimum water pressure vital to ensure your sprinklers are functioning effectively.

The sprinkler system’s water flow rate should be between 10 and 13 gallons per minute at 30 to 35 psi.

There are two alternatives: buy a water pressure gauge (like the one here) or get a professional plumber to come out and check the pressure.

Buying a water pressure gauge online is the most cost-effective solution due to the low cost of these instruments.

An expert is probably going to charge you considerably more than the gauge. Fill up a 5-gallon bucket with water from the sprinkler pipe and how long it takes to fill up. This will give you an idea of the gallons per minute.

Once you know the time it took, divide 60 by that number. For example, if it took 5 seconds to fill up the gallon bucket, it would be 60 / 5, or 12 gallons per minute.

At this point, you should have all the information you need to determine whether your water spout can accommodate sprinklers.

If you don’t have adequate pressure, you may need to call out an expert to evaluate your water pressure.

Permissions may be required, so check with your city before making any purchases.


Your city will be most anxious about where you are excavating and making sure you aren’t digging where there are lines underground. Permits may be required in your city, so check with them.

The last thing you want is to annoy someone in your city or accidentally dig up wires and then have many difficulties to solve.

You also can wind up being fined if you don’t call the city. You should thus get in touch with them and get any relevant licenses.

Figure out how you are going to dig the trenches


Trench digging may be accomplished in a variety of ways.

  • Using a pickaxe


Depending on the sort of soil you have in your yard, this may not be a suitable solution. The pickaxe is useful for breaking up hard-packed dirt. Then you would use a shovel to move the dirt out of the earth.

This would make for a lot of labor if your yard is vast (like our 3/4 acre yard), but you might get a nice workout and exercise.

  • Using a gas-powered trenching machine


This would be the simplest choice for digging your trenches if you have the resources. And it would accomplish the task significantly quickly for you.

If you live in an area with many rocks, this might be a difficulty, so be prepared with a pickaxe and a shovel.

Determine the location of the water supply.

Make sure you have an understanding of where the water is coming from. Once, we acquired a property that we assumed had water rights for our yard.

During the first spring season, we were shocked to learn that we lacked legal access to water. So for a few weeks, we were out of luck until we chatted to a neighbor and found out where the water was coming from.

We had to find a way to transport the water to where we needed it after discovering there was water there.

Sprinklers are useless if you don’t know where the water is coming from, as was the case here. So make sure you know you have water and if so, be sure to know where it is coming from.

Count the number of valves you’ll need.

Zoning is another name for valves. They both imply the same thing. Depending on the size of your yard and how much water pressure you have, this will assist in calculating how many zones you should have.

First, calculate how many gallons per minute your water supply delivers. Next, calculate the flow rate required by your sprinklers.

After that, divide the water source’s flow rate by the sprinklers’ flow rate. Use this tool to find out how many sprinklers may be placed in a zone.

For example, if your water supply offers 15 gallons per minute and your sprinklers demand 3 gallons per minute, you may set 5 sprinklers in one zone.

Then, calculate how many sprinklers you need to determine the number of zones.

Calculate the amount of plumbing you’ll need.


It should be relatively straightforward to determine the plumbing you need. You first need to have the diagram of your yard and where you have sprinklers/hoses running.

After that, you’ll be able to figure out how much pipe you’ll need. A 50-foot-by-50-foot yard with three sprinkler zones would need a minimum of 150 feet of pipe, to begin with.

After that, you’ll need to run a pipe from the water supply to the zone’s beginning. You’ll need an extra 225 feet of pipe for a zone that’s 50 feet away from the water source and another 25 feet away.

The 225 feet you’ll need are not included in this price, but you already know you’ll need them.

Assess your options for sprinklers and make a decision


There are all various sorts of sprinkler heads.

They include:

  • Pop up – this sprinkler head starts underground, and then when the sprinkler obtains water pressure, it will “pop up” out of the earth. This is excellent since it conceals the sprinkler away until it is utilized. As long as your kids don’t jump on them, it’s a good choice if you have young children since they are properly protected.
  • Sprinkler heads that are permanently elevated above the ground are known as “raised.” These are most often seen in gardens, but they may also be found in your typical backyard. Be cautious that someone strolling past may run into it and break it.


There are also numerous sorts of spraying options:

  • These sprinklers will emerge from the earth and remain firmly in place in the future. The smaller the yard, the better since they don’t have to cover as much ground.
  • When the sprinklers are activated, they will begin to revolve. Consequently, a huge area of the yard may be covered consistently.
  • Rotating: gear driven – these sprinklers will revolve. All of the gears of the sprinklers are constructed of plastic and are encased in a plastic case, keeping them safe while they are beneath the ground.
  • Golf facilities benefit greatly from rotating: big grass sprinklers like this. You’ll need a lot of water pressure, and it will cover quite a deal of area.
  • Misting Is generally used for gardens, as they cover just a tiny area. Can rotate, but don’t necessarily do.


Summary

Sprinkler system installation, despite its intimidating appearance, is rather simple. Before you begin, make sure you have a strategy in place and have purchased all of the necessary supplies. Then make sure you have a strategy to dig the trenches and then let the process begin.

Leave a Comment